Samsung Computer Drive SC 140 User Guide

CD-ROM DRIVE  
SC-140/148  
Safety Warnings  
The following diagrams illustrate the precautions to be taken when using your  
CD-ROM drive.  
User's Guide - ENGLISH  
You must not use the drive in any manner other than that specified in this guide.  
Do not attempt to repair the CD-ROM drive yourself. Contact your dealer or  
local SAMSUNG representative for all repairs.  
CAUTION  
Use of controls or adjustments or performance of procedures other than  
those specified here in may result in hazardous radiation exposure  
To reduce the risk of fire or electric shock, do not expose this appliance to rain or  
moisture.  
Please refer to the Samsung limited warranty statements.  
WARRANTY  
1
 
System Requirements  
Installing the Software  
Before you install the CD-ROM drive, we strongly recommend that you make certain  
that your set-up meets the system requirements listed below.  
You can install the device driver for DOS or for Windows.  
¡ Do not install DOS Driver when the program of Windows 95/98 is going on.  
(Remark CD-ROM Driver in the state of CONFIG. SYS.)  
Turn on your computer and wait for it to boot.  
Description  
Item  
1
IBM 486SX 20MHz (or higher) with  
an IDE interface(or a 100% IBM-  
compatible computer)  
Type of computer  
Insert the driver disk into a floppy disk drive(usually the A drive).  
2
3
If you are a...  
Then :  
Type a: at the DOS prompt  
Press the RETURN key  
5.25 inch  
Free expansion unit  
Disk space  
DOS user  
100KB minimum  
5.0(or higher)  
3.1(or higher)  
Access the File Manager  
Click on the A icon.  
Windows user  
MS-DOS version  
Windows version  
When you are in Windows 95/98, it is not  
necessary to install Device Driver.  
Whereas, when you are in Dos Mode of  
Windows 95/98, then install as follows.  
Click on MY COMPUTER icon.  
Click on the A icon.  
Windows 95/98 user  
Installing the CD-ROM Drive  
Install the CD-ROM drive in your computer horizontally, making sure that the Open/Close  
button is on the right.  
Run the CDSETUP program:  
4
5
To install the drive, proceed as follows.  
Then :  
If you are a...  
Turn OFF your computer. Remember to verify the  
configuration jumper on the rear of the CD-ROM drive.  
DOS user  
Type CDSETUP after the A: prompt  
Press RETURN  
1
Remove the cover of your PC. (main unit of the computer)  
Double-click CDSETUP.EXE from the Windows  
Windows user  
2
3
4
File Manager  
Remove the blank cover panel of the 5.25 inch unit in  
which the CD-ROM drive is to be installed.  
To...  
Confirm the installation  
Then enter...  
Y
Connect the CD-ROM drive to the IDE interface and power  
cables Iocated inside your computer.  
Connectors are keyed so it is impossible to put them in  
an incorrect position. Do not force the connectors, if they  
do not seem to fit.  
Exit without installing  
Result :  
N
If you answer Y(Yes), the installation program automatically  
Creates a SAMSUNG directory on your hard disk  
Copies the required softwares (mscdex.exe and sscdrom.sys)  
Modifies the CONFIG.SYS and AUTOEXEC.BAT files  
Install the CD-ROM drive into the unit and secure it with  
mounting screws. (recommended standard M3x6x4)  
5
6
When the Setup Completed screen is displayed, remove the installation  
floppy disk from the drive.  
6
7
Depending on your PC model, you may need to  
attach guide rails to the drive, so that the drive is  
held firmly in place.  
Reboot your system.  
If you use screws that are longer than the  
recommended standard, you may damage the  
drive.  
The computer restarts  
Both the device driver and MSCDEX are loaded  
Result :  
Put the cover back on your PC.  
4
5
 
Resolving Technical Problems  
Technical Specifications  
Please consult the following table BEFORE contacting your dealer or local SAMSUNG  
representative.  
SAMSUNG continually strives to improve its products. Both the design  
specifications and these user instructions are thus subject to change without  
notice.  
Problem  
Meaning / Solution  
SECTIONS  
Disc types supported  
SC-140  
SC-148  
CD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1,  
Form-2, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session),  
Video CD ready, Enhanced CD, CD-I/FMV, CD-R  
The software installation failed  
Check that your hard disk is not full.  
DISC  
The installation floppy disk may be corrupted.  
Repeat the installation with the backup floppy disk.  
Disc diameter  
12cm or 8cm  
Max. 6000KB/s  
PIO Mode - 4. DMA MW2  
80ms(typical)  
Max. 7200KB/s  
Data transfer rate  
I re-booted my PC and it paused  
during the start-up program.  
After installing the device driver, your system  
start-up program may take more time than  
expected. If it does not start-up after 60 seconds,  
verify your AUTOEXEC. BAT file and, if  
70ms(typical)  
Access time (1/3 stroke)  
Data buffer capacity  
Laser  
128KB  
DRIVE PER -  
FORMANCE  
Semiconductor Laser  
Gear motor  
necessary, contact your local computer dealer.  
Slide mechanism  
Spindle motor  
The disc tray does not open.  
The drive may not be installed correctly. Verify the  
physical installation.  
Brushless motor  
Loading type  
Tray Loading, DC motor(Soft Eject)  
12  
9
ERROR RATE  
FRONT PANEL  
Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bits  
In the File Manager, the CD-ROM If you have installed the Then ...  
CD-ROM drive ...  
Button  
Open/Close  
icon does not display.  
Indicator(LED)  
Headphone output  
Volume control  
Required power  
Busy  
And the software  
Re-boot your PC.  
Stereo Mini - jack (¯ 3,6 mm) 0.60 ± 20% (Vrms) 33½  
Dial type  
And have not installed  
the software  
Install the software  
following the instructions  
on page 5.  
+5V DC 1.7A,  
+12V DC 1.0A  
REAR PANEL  
ATAPI  
Interface connector  
Audio output  
Jumper block  
Work area  
I installed the software and re-  
booted my PC. The CD-ROM  
drive icon/directory still does not  
appear.  
When the program of Windows 95/98 is broken up, re-stall  
Line out 0.70 ± 20%(Vrms), 47k½  
Device configuration jumper  
it as the computer can not read the program anymore.  
Verify the connections between the drive and your PC.  
Check that the 40-pin flat cable is connected to an IDE  
interface (some PCs are equipped with an SCSI disk  
interface).  
OPERATING  
ENVIRONMENT  
Temperature : 5~45 ¡C, Humidity : 8~80%  
Temperature : -40~60 ¡C, Humidity : 5~90%  
Storage area  
Dimensions  
149(W) x 42.5(H) x 200(D)mm  
(Including bezel)  
Verify your AUTOEXEC. BAT file. Go to page 5 for  
the verification procedure.  
GENERAL  
Check the LASTDRIVE = command in the CONFIG. SYS  
file. The specified letter must take the CD-ROM volume  
into account. If you do not know which letter is assigned  
to the CD-ROM, enter Z.  
Net weight  
950g  
MTBF  
125,000 POH(Duty 20%)  
30,000 times  
RELIABILITY  
Disc compartment loading  
Using the documentation provided with your PC, check  
that the IDE hard disk is set up in MASTER mode.  
6
7
 

Radio Shack Microphone 33 3024 User Guide
RCA Flat Panel Television HD52W64 User Guide
Reliable Sewing Machine MSK 555 User Guide
Ryobi Trimmer 767r User Guide
Samsung Clothes Dryer DC68 02347B EN User Guide
Sanyo Vacuum Cleaner SC K140T User Guide
Seagate Computer Drive ST136403LW LC User Guide
Seagate Thermostat ST34520N W WC LW LC User Guide
Sears Lawn Aerator S A T 4 0 B H User Guide
SEH Computertechnik Planer IC146 ETHER HP FL User Guide