Rosewill Network Card RC216 User Guide

SATA II / ATA 133 PCIe Card RC216  
User Manual  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
z
1x Manual  
z
z
z
1x Driver CD  
1x SATA Data Cable  
1x ATA 133 IDE Cable  
Note: Contents may vary depending on country/market.  
3
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
Hardware Description  
G (Jumper Settings)  
JP  
Description  
Active Port  
J1-J4  
1-2 close  
2-3 close  
1-2 close  
2-3 close  
Enable SATA Port CON1  
Enable SATA Port CON3  
Enable SATA Port CON2  
Enable SATA Port CON4  
J5-J8  
Note: There are four SATA ports in PCIe SATA II 300 + PATA Raid Card.  
We name these ports CON1 to CON4. Ports CON3 & CON4 are  
internal SATA ports and CON1 & CON2 are external SATA ports. By  
4
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
changing the jumper setting on the PCIe SATA II 300 + PATA Raid Card  
that allows you to select between external and internal ports to use. By  
default, Port CON1 & CON2 are working.  
Hardware Installation  
1.  
2.  
3.  
4.  
Turn Off the power to your computer.  
Unplug the power cord and remove your computer’s cover.  
Remove the slot bracket from an available PCIe slot.  
To install the bard, carefully align the card’s bus connector with the  
selected PCIe slot on the motherboard. Push the board down  
firmly.  
5.  
Attach your internal or external devices to the PCIe SATA II 300 +  
PATA Raid Card.  
6.  
7.  
Replace the slot bracket’s holding screw to secure the card.  
Replace the computer cover and reconnect the power cord.  
RAID Arrays  
RAID Arrays are setup in the PCIe SATA II 300 + PATA Raid Card’s BIOS.  
There are four configurations supported:  
RAID level/Type  
RAID 0  
Configurations  
Disk Striping  
Disk Mirroring  
Number of disks needed  
2 or 3 or 4  
2
RAID 1  
5
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
RAID 0+1  
Disk Striping  
Mirroring  
Disk Concatenation  
4
+
JBOD  
2 or 3 or 4  
RAID 0 (Striping)  
1.  
As the BIOS boots press Ctrl+J when prompted to enter the RAID  
BIOS.  
2.  
3.  
4.  
At the next screen select Create RAID Disk Drive, press Enter.  
Enter RAID name, press Enter.  
Please use arrow keys and to switch the RAID level to  
0-Stripe, then press Enter.  
5.  
6.  
Please use arrow keys and to switch the disk, use the “space”  
key to mark the selected disk, then press Enter.  
Please use arrow keys and to select chunk size from 4K, 8K,  
16K, 32K, 64K or 128K, then press Enter.  
7.  
8.  
Input the RAID size, press Enter.  
When asked Created RAID on the select HDD (Y/N)?, press Y to  
accept.  
9.  
At the next screen select Save And Exit Setup, press Enter. When  
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.  
RAID 1 (Mirroring)  
1. As the BIOS boots press Ctrl+J when prompted to enter the RAID  
6
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
BIOS.  
2.  
3.  
4.  
At the next screen select Create RAID Disk Drive, press Enter.  
Enter RAID name, press Enter.  
Please use arrow keys and to switch the RAID level to  
1-Mirror, then press Enter.  
5.  
Please use arrow keys and to switch the disk, use the “space”  
key to mark the selected disk, then press Enter.  
Input the RAID size, press Enter.  
6.  
7.  
When asked Created RAID on the select HDD (Y/N)?, press Y to  
accept.  
8.  
At the next screen select Save And Exit Setup, press Enter. When  
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.  
CONCATENATION (JBOD)  
1.  
As the BIOS boots press Ctrl+J when prompted to enter the RAID  
BIOS.  
2.  
3.  
4.  
At the next screen select Create RAID Disk Drive, press Enter.  
Enter RAID name, press Enter.  
Please use arrow keys and to switch the RAID level to  
JBOD-Concatenate, then press Enter.  
5.  
6.  
Please use arrow keys and to switch the disk, use the “space”  
key to mark the selected disk, then press Enter.  
Input the RAID size, press Enter.  
7
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
7.  
8.  
When asked Created RAID on the select HDD (Y/N)?, press Y to  
accept.  
At the next screen select Save And Exit Setup, press Enter. When  
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.  
RAID 0+1 (Striping + Mirroring)  
1.  
As the BIOS boots press Ctrl+J when prompted to enter the RAID  
BIOS.  
2.  
3.  
4.  
At the next screen select Create RAID Disk Drive, press Enter.  
Enter RAID name, press Enter.  
Please use arrow keys and to switch the RAID level to  
01-Stripe+Mirror, then press Enter.  
5.  
Please use arrow keys and to select chunk size from 4K, 8K,  
16K, 32K, 64K or 128K, then press Enter.  
6.  
7.  
Input the RAID size, press Enter.  
When asked Created RAID on the select HDD (Y/N)?, press Y to  
accept.  
8.  
At the next screen select Save And Exit Setup, press Enter. When  
asked Save to disk &Exit (Y/N)?, press Y to exit the BIOS.  
Delete RAID Disk Drive  
1.  
As the BIOS boots press Ctrl+J when prompted to enter the RAID  
BIOS.  
8
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
2.  
3.  
At the next screen select Delete RAID Disk Drive, press Enter.  
Please use arrow keys and to select the array you want to  
delete, use the “space” key to mark the selected array, then press  
DEL.  
4.  
When asked ALL DATA ON THE RAID WILL LOST!! ARE YOU  
SURE TO DELETE (Y/N), press Y to accept.  
Solve Mirror Conflict  
When a RAID set is created, then metadata written to the disk includes  
drive connection information. If, after a disk failure, the replacement disk  
was previously part of a RAID set (or used in another system), it may  
have conflicting metadata. If so, this will prohibit the RAID set from being  
either created or rebuilt, in order for the RAID set to function properly,  
this old metadata must be first overwritten with the new metadata. To  
resolve this, from the main BIOS window select Solve Mirror Conflict,  
then press Enter, the correct metadata, including the correct drive  
connection information, will be written to the replacement disk.  
Rebuild Mirror Drive  
When a failure to one member occurs, you will be notified by the RAID  
BIOS during boot. The steps below will guide you in rebuilding a failed  
mirror set.  
1.  
Replace he failed drive(s) with one of equal or greater capacity, then  
9
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
start the computer.  
2.  
During boot press Ctrl+J to enter the RAID BIOS.  
3.  
4.  
Select Rebuild Mirror Drive press Enter.  
Please use arrow keys and to select the array you want to  
rebuild, press Enter.  
5.  
6.  
Please use arrow keys and to select the destination disk,  
press Enter.  
When rebuilding is finished, select Save And Exit Setup, press  
Enter. When asked Save to disk &Exit (Y/N)?, press Y to exit the  
BIOS.  
BIOS Configuration  
The PCIe SATA II 300 + PATA Raid Card BIOS will appear every time your  
system starts up. During this (POST) process, the BIOS will show up and  
indicate the devices attached to it.  
Driver Installation  
For Windows® 2000, XP and Server 2003  
For New Installation  
A new installation requires a floppy disk for the driver installation. To  
make this floppy disk, copy the contents of the “RC-216\Floppy32”  
folder, found on the driver CD, onto a blank floppy disk then follow the  
10  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
directions below.  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Setup the RAID Array prior to Windows installation.  
Follow Microsoft’s Windows installation procedure.  
Restart the computer when prompted by Windows’ installation.  
At the Windows Setup screen, press F6 to install the RAID driver.  
When prompted, press S to specify the location of the driver.  
Insert the floppy disk, then press Enter.  
Select (Windows 2000) RAID Driver for JMicron JMB363  
Controller or (Windows XP/2003) RAID/AHCI Driver for JMicron  
JMB36X Controller, then press Enter.  
8.  
Press Enter to finish driver installation, then follow the on-screen  
instructions to complete the Windows installation.  
For An Existing Installation  
1.  
Setup the RAID Array prior to driver installation and boot up to  
Windows.  
2.  
3.  
At the Found New Hardware Wizard window pop-up, please click  
Cancel button to cancel the driver installation for the device at this  
moment. The driver for this device will be installed in the next step.  
Please insert the CD driver bound with PCIe SATA II 300 + PATA  
Raid Card into your CD-ROM Drive.  
4.  
5.  
At the Windows desktop, click Start, then Run.  
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your  
11  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
CD-ROM drive letter)  
6.  
7.  
Follow the on-screen instructions to complete the installation.  
Restart Windows to complete the installation.  
For Windows® XP-x64/Server 2003-x64  
For New Installation  
A new installation requires a floppy disk for the driver installation. To  
make this floppy disk, copy the contents of the “RC-216\Floppy64”  
folder, found on the driver CD, onto a blank floppy disk then follow the  
directions below.  
1. Setup the RAID Array prior to Windows installation.  
2. Follow Microsoft’s Windows installation procedure.  
3. Restart the computer when prompted by Windows’ installation.  
4. At the Windows Setup screen, press F6 to install the driver.  
5. When prompted, press S to specify the location of the driver.  
6. Insert the floppy disk, then press Enter.  
7. Select (Windows XP/2003 x64) RAID/AHCI Driver for JMicron  
JMB36X Controller, then press Enter.  
8. Press Enter to finish driver installation, then follow the on-screen  
instructions to complete the Windows installation.  
For An Existing Installation  
1. Setup the RAID Array prior to driver installation and boot up to  
12  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
Windows.  
2. At the Found New Hardware Wizard window pop-up, please click  
Cancel button to cancel the driver installation for the device at this  
moment. The driver for this device will be installed in the next step.  
3.  
Please insert the CD driver bound with PCIe SATA II 300 + PATA  
Raid Card into your CD-ROM Drive.  
4.  
5.  
At the Windows desktop, click Start, then Run.  
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your  
CD-ROM drive letter)  
6.  
7.  
Follow the on-screen instructions to complete the installation.  
Restart Windows to complete the installation.  
For Windows® Vista  
For New Installation  
A new installation requires a floppy disk for the driver installation. To  
make this floppy disk, copy the contents of the “RC-216\Floppy32”  
folder, found on the driver CD, onto a blank floppy disk then follow the  
directions below.  
1. Setup the RAID Array prior to Windows installation.  
2. Follow Microsoft’s Windows installation procedure.  
3. Restart the computer when prompted by Windows’ installation.  
4. At the Windows Setup screen, press Load Driver to install the  
driver.  
13  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
5. Insert the floppy disk, please select JMicron JMB36X Controller  
(A:\jraid_f.inf), then press Next. (Change A:\ to match your floppy  
drive letter)  
6. Follow the on-screen instructions to complete the Windows  
installation.  
For An Existing Installation  
1. Setup the RAID Array prior to driver installation and boot up to  
Windows.  
2. At the Found New Hardware Wizard window pop-up, please click  
Cancel button to cancel the driver installation for the device at this  
moment. The driver for this device will be installed in the next step.  
3.  
Please insert the CD driver bound with PCIe SATA II 300 + PATA  
Raid Card into your CD-ROM Drive.  
4.  
5.  
At the Windows desktop, click Start, then Run.  
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your  
CD-ROM drive letter)  
6.  
7.  
Follow the on-screen instructions to complete the installation.  
Restart Windows to complete the installation.  
For Windows® Vista-x64  
For New Installation  
A new installation requires a floppy disk for the driver installation. To  
14  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
make this floppy disk, copy the contents of the “RC-216\Floppy32”  
folder, found on the driver CD, onto a blank floppy disk then follow the  
directions below.  
1. Setup the RAID Array prior to Windows installation.  
2. Follow Microsoft’s Windows installation procedure.  
3. Restart the computer when prompted by Windows’ installation.  
4. At the Windows Setup screen, press Load Driver to install the  
RAID driver.  
5. Insert the floppy disk, please select JMicron JMB36X Controller  
(A:\jraid_f.inf), then press Next. (Change A:\ to match your floppy  
drive letter)  
6. Follow the on-screen instructions to complete the Windows  
installation.  
For An Existing Installation  
1. Setup the RAID Array prior to driver installation and boot up to  
Windows.  
2. At the Found New Hardware Wizard window pop-up, please click  
Cancel button to cancel the driver installation for the device at this  
moment. The driver for this device will be installed in the next step.  
3.  
Please insert the CD driver bound with PCIe SATA II 300 + PATA  
Raid Card into your CD-ROM Drive.  
4.  
At the Windows desktop, click Start, then Run.  
15  
 
SATA II/ATA 133 PCIe Card RC216  
User Manual  
5.  
Type D:\ RC-216\Setup.exe, click OK. (Change D:\ to match your  
CD-ROM drive letter)  
6.  
7.  
Follow the on-screen instructions to complete the installation.  
Restart Windows to complete the installation.  
To Verify Driver Installation  
Click on the “Device Manager” tab in System Properties, which you  
access from the Windows Control Panel. You should see an “JMicron  
JMB36X Controller” installed under “SCSI and RAID controllers”  
item.  
Thank you for purchasing a quality Rosewill Product.  
support for your product.  
16  
 

Quantum Wheelchair INFMANU4169 User Guide
Radica Games Games 76044 User Guide
Radio Shack VCR 112 16 549 User Guide
RCA Cassette Player SCT 560 User Guide
Samsung Clothes Dryer DC68 02836B User Guide
Samsung Refrigerator RB194AB User Guide
Sanyo Digital Camera VCC HD4000 User Guide
Sanyo Heat Pump APR P1350BA User Guide
Sanyo Heat Pump WCHDX20053 User Guide
Seagull Guitars Guitar S6 User Guide