Radio Shack Motorized Toy Car 60 440 User Guide

XMODS® Street Custom RC  
Metal Bearings Upgrade Kit  
Ins ta lla tion Difficulty: ADVANCED  
60-440  
Upgrade from standard plastic to metal ball bearings for reduced friction, greater precision, and better handling. Before  
installing, turn off your vehicle and controller, then detach the car body.  
Hint: Carefully count and set aside screws while disassembling so you can properly re-assemble later.  
Upgrading the Metal Bearings for your XMODS  
Use the lug wrench  
1 supplied in your Starter Kit  
to detach each of the lug  
nuts and wheels.  
Take out the rear differential gear  
6 unit, and replace the bearing on  
both ends.  
Install the differential gear  
7 assembly into the rear drive  
unit and insert the drive shafts  
at both sides.  
If you have installed the All  
Remove the screw on the  
2 knuckle cap (or disk brake if  
you have changed it on your  
older EVO model). Carefully  
unlatch the claw and pull out  
the wheel shaft and knuckle  
cap/disk brake.  
Wheel Drive kit, skip to Step 9.  
Align the rear arm shaft to  
8 their holes and replace the  
rear drive unit. You might  
find it easier to remove  
the dampers, and reinstall  
them after you attach the  
rear drive unit.  
Remove the bearings on both ends of  
3 the wheel shaft. Wipe the grease off  
the wheel shaft and install the metal  
bearings. The grease ensures smooth  
operation with the original bearings.  
When you use the metal bearings,  
grease is not necessary.  
If you have not installed  
the All Wheel Drive kit,  
this completes the procedure.  
If you have installed the  
9 All Wheel Drive kit:  
Detach the center gear  
and shaft and replace the  
small bearing on the center  
shaft with the small metal  
bearing. Tweezers might  
help with this step.  
Align the drive shaft to the joint cup and  
4 reassemble the wheel shafts with the drive shaft  
installed into the knuckles. Then, replace the  
knuckle caps/disk brakes and wheels. Unless you  
have installed the All Wheel Drive kit, your front  
wheels do not have a drive shaft/joint cup, so just  
reassemble the front wheel shaft.  
Place the center gear on the  
10 center shaft. Lightly press and  
rotate the center gear so the flat  
side of the center shaft and the  
center gear lock together.  
Restore the center shaft and center gear into their  
11 original positions and rotate so the front center gear  
meshes with the shaft.  
Remove the two screws  
5 that hold the rear drive  
unit and detach it.  
Align the rear arm shafts  
12 to matching holes and  
replace the rear drive unit.  
You might find it easier  
to remove the dampers  
first. Reinstall them after  
attaching the rear drive  
unit.  
Remove the upper screw  
first. Move the rear upper  
arm and rear attachment  
holder out of the way,  
then, remove the lower  
screw.  
1
 
Align the drive shaft to the joint cup and  
Re-assemble the motor, the motor holder, and the  
4 reassemble the wheel shafts with the drive shaft 10 motor connector. If you have NOT installed the  
installed into the knuckles. Then, replace the  
knuckle caps/disk brakes and wheels. Unless you  
have installed the All Wheel Drive kit, your front  
wheels do not have a drive shaft/joint cup, so just  
reassemble the front wheel shaft.  
All Wheel Drive kit, this completes the upgrade.  
Remove the two screws on the motor connector  
5 and the two screws on the motor cover and detach  
the motor.  
If you have installed the All Wheel Drive kit:  
11 Remove the center gear and the center shaft and  
replace the small bearing. Tweezers may be helpful  
for this step.  
Remove the two screws on the rear drive unit  
6 to remove the rear gear case. Then, remove the  
differential gear and the third gear.  
Place the center gear back on  
12 the center shaft. Lightly press  
and rotate the center gear so the  
flat side of the center shaft and  
the center gear mesh.  
Replace the bearing on its both ends of the  
7 differential gear. If you have installed the All  
Wheel Drive kit, skip to Step 11.  
Restore the center shaft with center gear into the  
13 original position and rotate center gear so the front  
center gear meshes with the shaft.  
Reinstall the third gear, then align the drive shafts  
14 and restore the rear differential gear unit as shown.  
Align the drive shaft and restore the rear differential  
8 gear unit as shown.  
Align the shafts of the rear arms and re-assemble  
9 the rear gear case.  
Align the shafts of the rear arms and reassemble  
15 the rear gear case.  
3
 
Reassemble the motor and the motor holder. Route  
Reattach the center gear to the center shaft. Lightly  
16 the wire through the strain relief hook on the left 20 press and rotate the center gear so the flat side of  
side.  
the center shaft and the center gear mesh.  
Restore the center shaft with center gear to their  
21 original positions, and rotate the center gear so the  
rear center gear meshes with the shaft.  
Take out the front differential gear unit and replace  
22 the bearings on both sides of the gear.  
Remove two screws each from the tie rod holder  
17 and the tie rod, then remove one screw to detach  
the mud guard.  
Tie rod holder  
Tie rod  
Mud guard  
Restore the front differential gear unit as shown in  
23 the illustration.  
Remove the three screws on front gear case to  
18 detach it.  
Align the front arm shafts to the proper holes and  
24 reassemble the front gear case.  
Front gear case screws  
Remove the front center  
19 gear and the center shaft  
and take out the small  
bearing. Tweezers may be  
helpful for this step.  
Reassemble the tie rod and tie rod holder, and then  
25 the mud guard.  
Limited Warranty  
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack company-owned stores and  
authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack  
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR  
PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA,  
PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.  
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise  
provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and  
products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts  
and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance,  
alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic  
damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
RadioShack Customer Relations  
300 RadioShack Circle, Fort Worth, TX 76102  
12/99  
60-440  
07A08  
INS-3362-US-08  
Printed in China  
©2008 RadioShack Corporation. All Rights Reserved.  
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.  
 

Ramsey Electronics Headphones SHA2 User Guide
RCA Camcorder SOLAM VIDEO CAMERA User Guide
RCA CRT Television F19627 User Guide
RCA DVD Player DRC260 User Guide
RCA VCR VCR VR708HF User Guide
RCA VCR VR613HF User Guide
Roberts Radio Cassette Player SRC955 User Guide
Sabrent TV Converter Box TV PC85 User Guide
Samsung Microwave Oven SMH6140WB User Guide
Schumacher Battery Charger SE 3612 User Guide