RCA CD Player 42 7011 User Guide

42-7011  
Dual-Tray CD Player/Recorder  
A QUICK LOOK AT THE REMOTE  
Refer to your Owner’s Manual for complete instructions.  
PLAYING A CD  
CONNECTING AND POWERING YOUR RECORDER  
Follow the diagram to connect your recorder to your receiver.  
You can use the RECORD/PLAYBACK tray to play back CD, CD-R, and CD-  
RW discs. You can use the PLAYBACK tray to play back CD and finalized  
CD-R/CD-RW discs. You cannot play CD-R/CD-RW discs that have not  
been finalized on the PLAYBACK tray.  
1. Press POWER on the recorder. READING flashes for a while. When no  
disc is set, no DISC or DISC no appears.  
2. Press the respective OPEN/CLOSE for the PLAYBACK tray or the  
RECORD/PLAYBACK tray.  
S-VIDEO IN  
S-VIDEO OUT  
3. Carefully place the disc, label side up, into the recessed CD holder.  
4. Press OPEN/CLOSE for the PLAYBACK tray or the RECORD/  
PLAYBACK tray to close the disc tray. When a disc is loaded into the  
recorder, READING flashes as it determines the contents of the disc.  
When the recorder reads the TOC (Table of Contents), the display shows  
the total number of tracks, total play time, and the type of disc (the  
RECORD/PLAYBACK tray only).  
Note: The receiver, shown above, does not have digital out jacks. If your  
receiver also does not have digital out jacks, you can use a digital source such as  
a CD player or MD player.  
• When a blank disc is set on the RECORD/PLAYBACK tray, BLANK  
appears.  
A QUICK LOOK AT THE RECORDER  
• When a disc is set on the RECORD/PLAYBACK tray, the display shows  
one of the following:  
MUSICSKIP  
Buttons  
AUTO  
MANUAL  
DUBBING  
MODE  
SYNC REC  
OPEN/  
CLOSE  
RECORD  
INSTALLING BATTERIES  
OPEN/  
CLOSE  
DIGITAL REC  
LEVEL –/+  
CD — a commercial pre-recorded CD.  
CD-R — finalized CD-R.  
POWER  
MUSIC SKIP Buttons  
1. Press down on the battery compartment cover and slide it  
off in the direction of the arrow.  
REMOTE  
SENSOR  
CD-R, NO TOC — a CD-R which has yet to be finalized.  
CD-RW, NO TOC — a CD-RW which has yet to be finalized.  
CD-RW — a finalized CD-RW.  
2. Insert the batteries into the battery compartment as  
indicated by the polarity symbols (+ and ) marked inside.  
PHONES  
FINALIZE  
ERASE  
INPUT  
SELECTOR  
3. Replace the cover.  
PLAY  
PLAY  
STOP  
PAUSE  
PAUSE  
BLANK — No disc or unreadable disc.  
STOP  
5. Press  
for the PLAYBACK tray or  
²
/ENTER for the RECORD/PLAYBACK tray to start playback.  
²
6. Press to temporarily stop playback. To resume playback, press or  
.
²
“Think RadioShack for all of Your  
CD Player/Recorder Accessories”  
7. Press to stop playback.  
G
If you set CDs on both the PLAYBACK tray and the RECORD/PLAYBACK  
tray, the recorder automatically plays the other CD when the current CD  
finishes. The CD recorder stops playing at the end of the second CD.  
Headphones  
Batteries  
Blank CD-R Discs  
Optical Cable  
Audio Cable  
CD Lens Cleaner  
RadioShack Corporation  
Fort Worth, Texas 76102  
© 2003 RadioShack Corporation. All Rights Reserved.  
03A03  
Printed in China  
 

RCA DVD Player DRC6318E User Guide
Ryobi Trimmer 750r User Guide
Ryobi Work Light P715 User Guide
Saab Air Conditioner 9 3 M03 User Guide
Samsung Cordless Telephone SH u740 User Guide
Samsung Digital Camera AD68 04795A User Guide
Samsung Printer ML 6060N User Guide
Sanyo Flat Panel Television AVL 279 User Guide
Sanyo Projection Television PLV HD2000E User Guide
Seiko Instruments Printer SLP 410 User Guide